The objective of this course is to present the features of control and protection systems as used on gas turbine installations. The previous tape GT 3 dealt with operating parameters and potential hazards thus laying the groundwork for study of control and protection devices.
- NERC CEH: 4
- NERC OPS Hours: 4
- NERC Standard Hours: 0
- NERC Simulation Hours: 0
- NERC PE Hours: 4
- NERC EO Credits: 0
Terminal Objective: The trainee shall describe objectives of gas turbine control.
- Enabling Objective: The trainee shall explain the purpose of gas turbine control.
- Enabling Objective: The trainee shall explain the gas turbine control loop.
- Enabling Objective: The trainee shall describe a typical local operator interface for gas turbine control.
- Enabling Objective: The trainee shall describe the major elements of a gas turbine control scheme:
- o Fuel systems
- o Air compression systems
- o Lube oil systems
- o Cooling systems (air, generator, bearing)
- o Temperature
- o Auxiliary power
- o Monitoring and protectionees shall describe elements of the basic control loop and explain parameters typically monitored in the operation of the control system.
Terminal Objective: The trainee shall describe an automatic start-up and operation of a gas turbine.
- Enabling Objective: The trainee shall list the prerequisites necessary for a successful start-up .
- Enabling Objective: The trainee shall describe normal shut-down of a gas turbine.
- Enabling Objective: The trainee shall describe the load control for a gas turbine including:
- o Governor and remote control
- o Generator control via prime mover input
- o Monitoring and protection
- o On-line auxiliary requirements
- o Provide an overview of operator interface to gas turbine control loop
- Enabling Objective: The trainee shall describe the differences in sequences of operation for each of the following:
- o Normal shut-down by automatic sequence
- o Normal shut-down by manual sequence
- o Emergency shut-down
Terminal Objective: The trainee shall describe the temperature control schemes for a typical gas turbine.
- Enabling Objective: The trainee shall describe the monitoring of combustor temperatures for each of the following:
- o Inlet temperature
- o Exhaust temperature
- Enabling Objective: The trainee shall describe how temperature impacts output.
- Enabling Objective: The trainee shall describe how typical assessment and interpretation of temperatures may require operator action.
- Enabling Objective: The trainee shall explain the importance of monitoring other temperatures for each of the following:
- o Generator
- o Turbine bearings
- o Ambient air
- o Cooling water
Terminal Objective: The trainee shall describe the safety and protection schemes for a typical gas turbine.
- Enabling Objective: The trainee shall describe safety systems for fuel handling.
- Enabling Objective: The trainee shall describe safety systems for combustion processes.
- Enabling Objective: The trainee shall describe protection scheme for the gas turbine for each of the following:
- o Air systems
- o Cooling systems
- o Fuel systems
- o Mechanical vibration
- o Temperature
- o Pressure
- Enabling Objective: The trainee shall provide a summary of major points that are monitored and alarmed in a gas turbine installation (including but not limited to above listed areas).
- Enabling Objective: The trainee shall explain the purpose of monitoring and controlling NOx emissions.
Lesson 1: Operator Interface
- The Control System
- Display of Information
- Control of Turbine Output
Lesson 2: Automatic Start-up and Operation
- Startup Permissives
- Automatic Startup
- Automatic Synchronization
- Governor Control
- Automatic Shutdown
Lesson 3: Temperature Control
- Temperature Measurement
- Measurement Reliability
- Combustion Trouble
Lesson 4: Safety and Protection Systems
- Alarms and Trips
- Flameout Detection
- Turbine Trips
- Vibration and Other Alarms
2504 Control and Protection Systems - No Regulator/ 360training.com
- No Regulator/ 360training.com
- Website URL:
- Email Address:
- 1381, Burnet Road, Suite 100, Austin, Texas, 78727.
2504 Control and Protection Systems - Registered Continuing Education Program RCEP
Subject Matter Expert
This course is created and brought to you by 360training, a leading provider of accredited e-learning courses to working professionals through today's leading schools, associations and corporations. 360training's high-quality e-learning courses assist thousands of working professionals in a wide range of disciplines, helping them to succeed in today's marketplace, to renew licenses, to acquire certification or to prepare for a new profession.
This course was created by the instructional design staff of 360training in connection with field professionals whose many years of experience in adult educational theory and distance learning technology make the process of certification, compliance and training as convenient, engaging and cost-effective as possible.
If you have any requests for technical or instructional support, then please contact the 360training Support Department located in the HELP section of your account profile. Technical support inquiries are handled immediately; instructional support questions are answered within 24 business hours, with information provided by a qualified professional in your field through our network of subject matter experts.
End of Course Instructions
Upon successful completion of the course and the accompanying survey, you will get your certificate and, if appropriate, have your success reported to the relevant regulatory body.
NERC CE: If you selected this option at the course launch, your credits will automatically be reported for NERC CE through the NERC SOCCED reporting tool. In case of reporting failure, your credits would be manually reported within 48 hours. It is important to provide the correct License Number in order to obtain the completion certificate and get reported. You can also use this Certificate for PDH Reporting and reporting to any other Regulator (example PJM, etc.).
RCEP: If you selected this option at the course launch, you will NOT receive a certificate directly from the training page. Instead, your credits will be reported to RCEP and you would receive a certificate from them through email.
360training: If you selected this option at the course launch, you are seeking NO credit reporting. The training you are taking is for professional development only. You will receive a generic 360 certificate.
You will not be required to pass the knowledge check questions to move on to the next lesson. These will not be counted as a grade, but each question gives you insight into what you should have learned and the sorts of things you'll need to remember moving forward.
Got questions? Contact us below or call 877-881-2235
Why Choose 360training.com?
- Fast and easy courses completion
- Get an education faster than at traditional colleges!
- 100% online - No classroom attendance required.
- Unlimited 24x7 online customer support
- Over 500,000+ certified nationwide.