Delaware Delaware 10 Hour Electrician CE Package

Delaware 10 Hour Electrician CE Package

18 Learner Reviews -

Read Reviews

85.00 85.00

This Package Contains Courses - See More
  • Course Delivery: On Demand
  • Language: English

Chat Live | Contact Us | Toll Free: (888) 360-8764



The following package is designed around NEC Code & NFPA Safety. It covers Chapters 4 through 8 of the 2014 NEC.  There will be certain terms that will be revisited from earlier chapters, but predominately its focus will be on additions to the Code as well as revised articles, sections, subsections and finally subdivisions. The author has given special attention to a minute portion of code changes for several reasons.

As an employee or an employer, it is important that you also understand the importance of electrical safety.

The NFPA 70E part of the package covers standards for electrical safety in the workplace. Throughout this course, you will review the relationship between the Occupational Safety and Health Administration (OSHA) and NFPA 70E. You will also review general NFPA 70E standards and the importance of these standards in maintaining your safety and the safety of others in the workplace.

Course Objectives

After completing this package, you will be able to:

  • Determine when a multipole snap switch can be fed by more than one circuit.
  • Understand the principle and functions of effective ground-fault current path.
  • Determine when an identified barrier is required to be securely fastened between two devices.
  • Discuss the reason(s) why 15 and 20 amp receptacles in damp and wet locations shall be listed weather resistant.
  • Discuss why the NEC now identifies switchgear separately from switchboards.
  • Identify the new term that has replaced the term fixture, and describe the new term’s inclusion.
  • Discuss the rationale for requiring all lamp holders and luminaires to be listed, including the addition of retrofit kits.
  • Identify labeling differences between photovoltaic (PV) DC converters.
  • Discuss the inclusion of the ID of Branch Circuits from DC Systems, as well as its application to Additional Load Calculation References.
  • Define Major Repair Garage and Minor Repair Garage.
  • Identify the hazardous painting area of an aircraft hangar.
  • Define, Operator and Portable Structure with regards to carnivals, circuses, fairs, and similar events.
  • Apply the requirements from Table 250.122 when sizing bonding conductors where multiple services or separately derived systems supply portable structures.
  • State the exception to 547.5 requiring GFCI-protected receptacles in dirt confinement areas for livestock.
  • Understand the concept of Equipotential Plane and its relevance to agricultural buildings.
  • Define the revised term, Section Sign, and demonstrate an ability to review the application of retrofit kits requirements.
  • Define the term, Abandoned Supply Circuits and Interconnecting Cables and discuss the relevance to a new install.
  • Apply the new requirements of 680.12 when servicing a pool, spa, hot tub, or fountain.
  • Apply the new requirement of equipotential bonding, during a pool installation.
  • Apply new GFCI protection requirements to pool pump motors.
  • Name the additional equipment used for photovoltaic power systems that are required to be identified and listed.
  • State the importance for connectors, lugs, or terminals that are intended for fine-stranded cables to be marked for their intended application.
  • Discuss the importance of critical operations power systems with regards to the separation of ground-fault protection.  
  • Discuss when the NEC would allow the practice of lacing with Bare Class 2 Conductors.

  • Define the term, Communication Circuit. State why the NEC has added requirements on intersystem bonding.

  • You will learn about safe work practices, maintenance requirements and NFPA 70E safety training requirements for specialized equipment. NFPA 70E training provides practical training for hazard identification, risk assessments, selection of PPE, establishing safe work environments and meeting employee training requirements.

The Following Courses Are Included In This Package:

Course Name Industry Course Delivery
NFPA 70E-Standard for Electrical Safety in the Workplace Trades and Engineering
NEC 2014 Code Change (5 Hr) - Delaware Trades and Engineering

Topics Covered

NEC 2014 Code Change 5 Hr

Lesson 1: Chapter 4 - Equipment for General Use

  • Switches
  • Receptacles, Cord Connectors, and Attachment Plugs
  • Switch Boards and Panel Boards
  • Luminaires and Lampholders and Lamps
  • Appliances
  • Motors, Motor Circuits, and Controllers Generators
  • Lesson Assessment

Lesson 2: Chapter 5 - Special Occupancies

  • Grounding Conductors
  • Major and Minor Garage Repairs
  • Aircraft Hangars
  • Health Care Facilities
  • Carnivals, Circuses, Fairs, and Similar Events
  • Lesson Assessment

Lesson 3: Chapter 6 - Special Equipment

  • Electric Signs and Outline Lighting
  • Swimming Pools, Fountains and Similar Installations
  • Solar Photovoltaic Systems
  • Lesson Assessment

Lesson 4: Chapter 7 - Special Conditions and Chapter 8 - Communications Systems

  • Capacity and Rating
  • Critical Operations Power Systems (COPS)
  • Optical Fiber Cables and Raceways
  • Communications Circuit
  • Lesson Assessment
  • Writing Assignment for NEC Course

NFPA 70E - Standard for Electrical Safety in the Workplace 2015 (5 Hr)

Lesson 1: Introduction to NFPA 70E

  • NFPA Incorporates OSHA Standards into NFPA 70E
  • Changes Adopted by NFPA 70E
  • Importance of NFPA 70E
  • Importance of Electrical Safety
  • Layout and Review of NFPA 70E
  • NFPA 70E Annexes

Lesson 2: Chapter 1 Safety-Related Work Practices

  • Safety-Related Work Practices
  • Article 100 Definitions
  • Article 105 Application of Safety-Related Work Practices
  • Article 110 General Requirements for Electrical Safety-Related Work  
  • Article 120 Establishing an Electrically Safe Work Condition
  • Article 130 Work Involving Electrical Hazards

Lesson 3: Chapter 2 Safety-Related Maintenance Requirements

  • Article 200 – Introduction
  • Article 205 – General Maintenance Requirements
  • Article 210 – Substations, Switchgear Assemblies, Switchboards, Panel boards, Motor Control Centers, and Disconnect Switches
  • Article 215 – Premises Wiring
  • Article 220 – Controller Equipment
  • Article 225 – Fuses and Circuit Breakers
  • Article 230 – Rotating Equipment
  • Article 235 – Hazardous (Classified) Locations
  • Article 240 – Batteries and Battery Rooms
  • Article 245 – Portable Electric Tools and Equipment
  • Article 250 – Personal Safety and Protective Equipment

Lesson 4: Chapter 3 Safety Requirements for Special Equipment

  • Article 300 Introduction
  • Article 310 Safety-Related Work Practices for Electrolytic Cells
  • Article 320 Safety Requirements Related to Batteries and Battery Rooms
  • Article 330 Safety-Related Work Practices for Use of Lasers
  • Article 340 Safety-Related Work Practices: Power Electronic Equipment
  • Article 350 Safety-Related Work Requirements: Research and Development Laboratories

Subject Matter Expert

This package is created and brought to you by 360training, a leading provider of accredited e-learning courses for working professionals through today's leading schools, associations, and corporations. 360training's high-quality e-learning courses assist thousands of working professionals in a wide range of disciplines, helping them to succeed in today's marketplace, to renew licenses, to acquire certifications, or to prepare for new professions.

End of Course Instructions

After successful completion of the course the certificate of completion will be available for download and print from the training homepage.

Quiz Information

Each quiz must be passed with a minimum of 75% to proceed to the next lesson.


The final exams must be passed successfully with 75% or higher in order to receive your certificate of completion.

Got questions? Contact us below or call 877-881-2235

* *
* *
* *

Why Choose

  • Fast and easy courses completion
  • Get an education faster than at traditional colleges!
  • 100% online - No classroom attendance required.
  • Unlimited 24x7 online customer support
  • Over 500,000+ certified nationwide.

18 Real Reviews From Actual Learners

Peter From Canton, MI Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:

very informative. I just hope there are exam every chapter.

Posted 11 months ago
Mark From Canton, MI Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:

narrator voice almost put me to sleep that is my only complaint

Posted 11 months ago
Aurelien From Canton, MI Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:


Posted 11 months ago
Joseph From , LA Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:

This was a good and informative training that gives one the knowledge of the required information to know what to look for in the job to be safe.

Posted 11 months ago
Jose From , Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:

very helpful

Posted 11 months ago
Jared From , Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:

Great Job by Kevin Ali for setting us up with this course...

Posted a year ago
Marco From Tehachapi, CA Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:


Posted a year ago
Andres From Tehachapi, CA Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:


Posted a year ago
Rick From , AA Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:

great course will recommend to anyone

Posted a year ago
Timothy From Tehachapi, CA Took NFPA 70E-Standard for Electrical Safety in the Workplace, And Said:


Posted a year ago